|
5/3/2016 Bought car 9/30/2017 Welded in cross braces (door opening) 9/30/2017 Put Car on rotisserie 10/19/2017 Cut out rear quarter panels, rear seat support and floor braces (that someone added) 11/11/2017 Removed Dash, removed metal from trunk dropoffs Welded-up small holes in firewall - mostly at heater opening,Repaired big center hole in firewall 12/13/2017 Stephen Dexter sandblasted shell - 7 hours (in 2 days) 12/30/2017 Moved car to workshop side of garage 1/1/2018 Put rear of shell up on milkcrates 1/5/2018 Started cutting out trunk pan 1/6/2018 Finished cutting out trunk pan 1/10/2018 Welded in rear floor section at RH rear seat belt mount location 1/11/2018 Welded in rear floor section at LH rear seat belt mount location 1/13/2018 Finished welding in rear floor sections at rear seat belt mount locations and dressed wells. 1/15/2018 Trimmed and fitted trunk pan 1/16/2018 Started welding in trunk pan 1/20/2018 Continued welding in trunk pan. Started dress welds 1/22/2018 Dressed a few welds by the tail panel 1/29/2018 Finished dressing wells by tail panel 1/30/2018 Welded in RH rear bumper brace in trunk 1/31/2018 Welded in LH rear bumper brace & LH shaker bracket in trunk 2/1/2018 Welded in RH shacker backet and welded trunk pan to frame rails at wheel wells. 2/6/2018 Cut out LH wheel house. 2/7/2018 Fit new LH wheel house pieces 2/10/2018 Welded in LH Wheel house 2/11/2018 Started repair on RH wheel house support 2/12/2018 Welded in upper portion of RH quarter inner brace 2/13/2018 Fabricated lower portion of RH quarter inner brace 2/14/2018 Completed welding in RH quarter inner brace 2/15/2018 Cut out RH wheel house. 2/17/2018 Fitted RH wheel house 2/19/2018 Welded in RH wheel house 2/20/2018 Trimmed and fitted RH quarter panel 2/22/2018 Fixed 2 holes in trunk. Trimmed RH rocker panel 2/23/2018 Finished repair on RH rocker panel. Extended RH outer wheel house to fit to rocker. 2/24/2018 Finished repair on LH rocker panel. Extended LH outer wheel house to fit to rocker. 2/26/2018 Dressed welds on LH wheel house area. 2/27/2018 Welded in missing LH shaker nut. Transferred conv top motor mount brackets to trunk floor. 3/1/2018 made rear seat brace wheel house plates 3/2/2018 Repaired read seat brace trunk panel 3/3/2018 Welded in rear upper shock mounts, started installing rear seat brace 3/5/2018 Started welding in rear seat brace 3/6/2018 Almost finished welding in rear seat brace 3/7/2018 Finished welding in rear seat brace and spare tire hold-down 3/8/2018 Fixed holes in tail panel 3/10/2018 Detailed trunk for priming. Masked off rear of car. 3/11/2018 Primed trunk area 3/12/2018 Fitted and made modifications to RH quarter skin 3/13/2018 Started welding in RH quarter panel. 3/14/2018 Continued welding in RH quarter panel. 3/15/2018 Ground down welds and welded up pin holes in RH quarter panel 3/17/2018 Finished welding and grinding on RH quarter panel. Completed filler work on panel. Have just jamb on top to fix before putting in primer. 3/19/2018 Started filler work on top of quarter. Welded holes in RH rocker. 3/20/2018 Finished filler work on top of quarter. Started filler work on RH rocker. 3/21/2018 Masked right side for priming. 3/22/2018 Primed RH quarter and rocker. Back primed LH quarter panel. 3/24/2018 Fitted LH quarter panel. Started buttwelding it into place 3/27/2018 Continued buttwelding LH quarter into place. 3/28/2018 Continued buttwelding LH quarter into place. 3/29/2018 Finished buttwelding LH quarter into place and ground down welds. 3/30/2018 Almost finished filler work on LH quarter panel. 4/2/2018 Finished filler work on face of LH quarter and rocker. Top of quarter almost done. 4/3/2018 Finished filler work on top of LH quarter. Started filler work on tail panel. 4/4/2018 Welded in trunk latch support. Continued tail panel filler work 4/5/2018 Finished filler work on tail panel. Started masking car. 4/7/2018 Primed tail panel, LH quarter and rocker panel. 4/9/2018 Connected rear to rotisserie. Started working on firewall. 4/10/2018 Continued welding up holes in firewall. 4/11/2018 Continued welding up holes in firewall. 4/12/2018 Continued welding up holes in firewall. 4/14/2018 Finished welding firewall holes. Started fixing LH toepan area 4/16/2018 Worked on LH toepan area 4/17/2018 Worked on LH toepan area 4/18/2018 Worked on LH toepan area 4/19/2018 Pulled jambs out of convertible floor reinforements. 4/21/2018 Fixed console area and RH toepan. 4/23/2018 Fixed damage in floor from roll bar ar LH rear rocker 4/24/2018 Ground down some welds on floorpan 4/25/2018 Fixed cutouts in lower seat reinforcements 4/26/2018 Cleaned welds on RH side of floor pan 4/28/2018 Cleaned up welds on floor pan 4/30/2018 Started fixing rust on lip at LH rocker panel 5/1/2018 Finished repair on LH rocker. 5/2/2018 Started filler work on underside of floors 5/5/2018 Continued filler work on floors 5/8/2018 Continued filler work on floors 5/12/2018 Primed undercarriage 5/14/2018 Started fitting dash 5/15/2018 Detailed inside floors and firewall 5/16/2018 Fit defrost duct to dash. Masked-off interior for priming 5/17/2018 Primed inside and underside of upper dash panel 5/20/2018 Weld in bottom portion of dash 5/21/2018 Finished welding in dash 5/22/2018 Detailed firewall 5/23/2018 Primed dash and firewall - bodywork now complete on shell 6/15/2018 Went to Camaro Specialties to buy front end sheetmetal 7/6/2018 Installed nose components 9/27/2018 Steven Dexter picked up the sheetmetal for sandblasting. 10/3/2018 Started repair on LH door (bottom left) 10/4/2018 Continued repair on LH door (bottom left) 10/10/2018 Finished metal repairs on LH door. Door fitted to car. 10/15/2018 Trimmed edge of LH door for better gaps 10/16/2018 Welded edge of LH door to improve gaps 10/17/2018 Removed LH door and started filler work 10/18/2018 Continued filler work on LH door 10/19/2018 Sheetmetal came back from sandblasting 10/20/2018 Completed major filler work on LH door 10/22/2018 Started filler work on RH door 10/23/2018 Continued filler work on RH door 10/24/2018 Completed major filler work on RH door 10/25/2018 Prepared parts for priming 10/27/2018 Primed parts (doors, upper filler, upper valance, front fender lower extensions). 2 cups DP50LF mixed. 10/29/2018 Installed doors 10/30/2018 Fixed holes in RH inner fender. Prepared for priming 10/31/2018 Started working on radiator support. 11/3/2018 Primed radiator support and inner fenders. Started working on front lower valance. 11/7/2018 Continues working on the front lower valance. Installed and aligned trunklid to check alignment prior to repair. 11/8/2018 Continues working on the front lower valance. 11/12/2018 Repaired trunklid underside at emblems. 11/13/2018 Ground down welds on trunklid underside at emblem holes 11/14/2018 Welded patch on LH front fender 11/15/2018 Finished welding on LH fender 11/17/2018 Add RS bracket to LH fender, started filler work on LH fender, primed lower RS valance 11/18/2018 Finished LH fender filler work and primed it. 11/23/2018 Started repair work on RH fender 11/24/2018 Continued repair work on RH fender and trunk lid 11/26/2018 Welded new bottom section to RH fender 11/27/2018 Cleaned welds on new bottom section on RH fender 12/1/2018 Primed RH fender, continued patching trunklid. 12/2/2018 Finished converting trunklid to 1967 style. Ready for filler work. 12/3/2018 Started filler work on trunklid 12/4/2018 Assembled nose.Finished fillerwork on trunklid 12/5/2018 Primed trunklid 12/6/2018 Installed trunklid. 12/7/2018 Repaired hood and started filler work. 12/11/2018 Continued filler work on hood. 12/12/2018 Continued filler work on hood. Started drilling fender emblem holes. 12/13/2018 Completed filler work on hood. 12/15/2018 Sanded underside of hood. Primed top of hood. Drilled RH fender emblem holes. 12/17/2018 Fixed holes on underside of hood 12/17/2018 Primed underside of hood 12/23/2018 Installed hood and aligned. Sanded car with 180 on DA. Started masking car 12/26/2018 Finished masking car, primed car with SlickSand then guide coat 12/28/2018 Started block sanding car 12/29/2018 Continued block sanding car. All done except for rockers and tailpanel 12/31/2018 Finished block sanding car. Trunklid needs another coat. 1/1/2019 Sanded upper door and upper interior quarter areas that will be blue 1/3/2019 Removed and sanded lower valance panel 1/5/2019 Apply SlickSand to trunk lid, lower valance and interior areas. Mostly dismantled subframe mounted components. 1/7/2019 Block sanded trunklid again. 1/8/2019 Block sanded rest of touched up body panels. Unmasked car and sanded cut-lines 1/9/2019 Sanded upper wiper/grill panel, started sanding lower valance. 1/12/2019 Finish sanding lower valance, finish sanding b-pillars 1/14/2019 Preped intake and heads for delivery to mahcine shop 1/21/2019 Drill holes on inside of LH fender for headlight relay mtg bracket. Dismantled nose. Also removed trunklid. 1/23/2019 Dropped heads and intake off at VT Engine Repair, started masking shell. 1/24/2019 Ordered dash paint from Instrument Specialties, continued masking shell 1/25/2019 Finished masking car 1/26/2019 Furnace problems. Dismantled conv top frame 1/27/2019 Primed everything except front fenders and lower valance- 3 full cups of mixed primer. 1/28/2019 Unmasked car, removed doors, started assembling rotisserie 2/2/2019 Fixed trialing arm stud, sanded undercarriage 2/3/2019 undercoated trunk and wheel wells. 2/4/2019 Sanded firewall 2/5/2019 Seam sealed inside car and firewall 2/6/2019 Masked car for painted undercarriage 2/7/2019 Wiped down undercarriage 2/8/2019 Primed and painted undercarriage (Hot Rod Black, 1 cup mixed) 2/9/2019 Added overspray details to undercarriage 2/11/2019 Unmasked car and sanded RH quarter panel (800 grit) 2/12/2019 Sanded LH quarter panel (800 grit) 2/13/2019 Finished sanding on shell 2/14/2019 Take car off rotisserie 2/16/2019 Cut body braces off, Seam sealed A-pillar & top of cowl, sanded doors with 800, installed doors. 2/18/2019 Dismantled from brake assemblies 2/19/2019 Stripped glove box door and hinge. 2/20/2019 Fixed dent in glove box door. Primed upper inner door panels, upper inner quarters, glove box door and glove box hinge 2/23/2019 Painted top of dash suede blue, sanded upper inner door panels, upper inner quarters, glove box door and hinge 2/26/2019 Sent door panel carpets out to Al Knoch. Painted dash face, upper windshield header, door upper and quarter upper panels 2/27/2019 Dismantled steering column 3/1/2019 Sent glove box door, painted hinge, paint can and chips to Instrument Specialities 3/2/2019 Dismantled pedal assembly, Prepared engine for assembly 3/5/2019 Installed head down pins and gaskets. Installed PCV canistor 3/6/2019 Installed cam and timing chain. Installed heads. 3/9/2019 Installed rocker arms, intake ant timing cover. Dismantled water pump. 3/11/2019 Installed oil pump and oil pan. 3/13/2019 Started masking car for repainting the dash. 3/14/2019 Masked Passenger's door 3/15/2019 Received confirmation of order from Al Knoch 3/16/2019 Finished masking car for repainting dash. 3/19/2019 Masked Engine for sandblasting 3/20/2019 Cleaned and Primed engine 3/21/2019 Painted engine (seymour paint), drained OER areosol cans into quart can for painting interior. 3/23/2019 Repainted dash face, upper windshield header, door upper and quarter upper panels. Seam sealed doors and trunklid. 3/25/2019 Started masking car for edging car in white. 3/26/2019 Primed trunk hinge springs. Finished masking. 3/27/2019 Edged doors, trunk, cowl and conv opening. All in white 3/29/2019 Painted Firewall and inside of trunk. Primed steering column parts 3/31/2019 Painted underside of trunklid & fixed RH door paint 4/1/2019 Unmasked Car 4/2/2019 Dismantled & cleaned oil canister 4/3/2019 Sanded front filler panel 4/4/2019 Sanded upper grill panel and front fender extensions 4/6/2019 Primed front fenders and lower valance 4/8/2019 Started sanding RH fender 4/9/2019 Finished sanding RH fender, stared sanding LH fender 4/10/2019 Finished sanding LH fender, fender extensions and lower valance. Started sanding trunklid. 4/13/2019 Applied slick sand to underside of hood. Stripped steering column parts. Painted A-pillar mouldings. 4/15/2019 Started sanding slick sand. 4/16/2019 Finished sanding underside of hood. 4/17/2019 Finished sanding rad support, inner fenders & front brace. Drilled holes in inner fenders for RS lights and dampeners. 4/18/2019 Primed and painted underside of hood, inner fenders & rad support 4/20/2019 Repainted underside of hood & inner fenders due to runs. 4/23/2019 Stared assembling steering column 4/24/2019 Assembled steering column 4/25/2019 Started sanding hood 4/27/2019 Finished sanding hood. Started cleaning garage. 4/29/2019 Steve Dexter picked up parts for sandblasting. Continued to clean garage. 4/30/2019 Continued to clean garage. Replaced ballast on one light 5/1/2019 Painted steering column and lower covers. 5/6/2019 Detailed subframe 5/7/2019 Wire wheeled suspension parts 5/8/2019 Wire wheeled suspension parts & heater box. Removed control arm bushings 5/9/2019 Installed lower control arm ball joints nad bushings 5/11/2019 Painted frame, control arms, backing plates, springs, etc 5/14/2019 Sent upper control arms out to have ball joints installed. 5/15/2019 Sandblast front suspension, brake & misc parts. 5/16/2019 Primed and painted front suspension, brake & misc parts. 5/18/2019 Sandblasted more parts 5/20/2019 Installed upper control arm bushings. Prepared parts for painting 5/21/2019 Painted upper control arms, brake drums, crossmember, engine parts, etc. 5/22/2019 Painted heater box and gauge bezel 5/25/2019 Painted ash tray opening OER interior Black lacquer 5/28/2019 Started masking car 5/29/2019 Continued masking car 5/30/2019 Painted bottom of rockers panels and fenders black 6/1/2019 Finished masked arranged parts for painting. 6/5/2019 Seam sealed B-pillar & tail panel top 6/10/2019 Painted car 6/14/2019 Started sanding body 6/15/2019 Started buffing body 6/17/2019 Finished buffing body, sanded trunklid 6/18/2019 Buffed trunklid, sanded hood 6/19/2019 Buffed hood, sanded RH fender 6/19/2019 Sanded LH fender, butfed fenders 6/21/2019 Installed trunklid. 6/22/2019 Finished sanding and buffing smaller parts, unmasked car, setup subframe for assembly. 6/24/2019 Installed control arms 6/25/2019 Painted front brake adjust springs 6/26/2019 Installed RH front brakes, painted sway bar 6/27/2019 Installed LH front brakes, wheel hubs and drums. Installed sway bar. Confirmed that Steering arms are 6.2" versions are for conv & BB cars. 7/1/2019 Assembled and Installed pedal support 7/5/2019 Applied gun bluing and RPM magic to steering center link and idler arm. 7/9/2019 Dismanlted steering gear box 7/10/2019 Sandblasted gear box, wiper motor housing and heater cables. 7/13/2019 Assembled steering gear box, primed and painted gear box, idler arms, heater blower housing and engine frame mounts. 7/18/2019 Installed master cylinder front brake lines, steering gear box, idler arm & engine frame mounts. Assembled heater box. 7/20/2019 Reassembled and painted wiper motor. Assembled tierods. Installed subframe clips. 7/22/2019 Installed steering linkage and wiper motor. 7/23/2019 Installed heater box and battery calbe clips on frame 7/24/2019 Installed dash pad and speaker. Installed wheels on subframe 7/25/2019 Installed dash harness 7/29/2019 Installed heater controls and courtesy light harness. Cleaned up radio. 7/30/2019 Installed cig lighter, ignition, wiper switch, RS dash harness & radio. Broke headlight switch 7/31/2019 Installed ashtray bracket, center bezel & glove box. Broke glove box wire. 8/1/2019 Fixed broken wire, installed flasher bracket and speedo cable 8/3/2019 Painted kickpanels, sandblasted small parts 8/6/2019 Assembled kickpanels 8/7/2019 Connected subframe. Installed headlight switch and tail light harness. 8/8/2019 Installed instrument cluster 8/10/2019 Installed steering column. Painted sill wire covers. Installed inner fender dust shields. 8/11/2019 Installed rocker wire covers. Applied touch up paint to inner fenders. 8/12/2019 Installed lower control arm bumpers and front brake lines to distrib block. Installed emblems on LH fender 8/13/2019 Installed door jamb light switches, kick panels and courtesy lights. 8/14/2019 Install speedo cable clamps. Partially installed front to rear brake line. 8/20/2019 Installed carpet guard, painted parking brake. Installed radio bezel. 8/21/2019 Started masking car for buff-through repair 8/22/2019 Finished masking car for buff-through repair 8/24/2019 Painted rear quarters due to buff-through repair 8/28/2019 Sanded and buffer rear quarters 8/30/2019 Dropped parts off to Steve Dexter to sandblast 8/31/2019 Installed rubber plugs and body pan plugs 9/4/2019 Primed rear shakers and a few top frame parts. 9/5/2019 Spatter Painted rear shakers and gas filler cover 9/7/2019 Fixed conv top front header and 2nd header 9/9/2019 Partially assembled LH conv top frame rail 9/10/2019 Sandblasted more top parts, trunk lock clip & RS head light parts 9/11/2019 Primed and painted top frame parts & RS headlight parts 9/24/2019 Installed missing rivet on RH top frame, primed and painted remainder of top frame parts. 9/25/2019 Install reverse lights, Assemble tail lights, Instaledl rear shakers 9/26/2019 Installed tail lights, trunk weather seal, trunk lock 9/27/2019 Installed parking brake. 9/30/2019 Installed RH fender and RAD support. Installed inner fender to LH fender 10/1/2019 Installed LH fender, lower valance & front shakers 10/2/2019 Finished nose assembly - less hood 10/3/2019 Installed headlight harness, volt reg and horn relay. 10/5/2019 Installed lower molding on LH door 10/7/2019 Installed LH spears and LH fender RS mouldings 10/8/2019 Assembly RH headlight asby a bit, installed RH spear molding 10/9/2019 Attached RH door moulding & RH quarter RS moulding 10/10/2019 Installed RH front RS moulding. Assembled parking lights 10/12/2019 Installed parking lights, RH door latch & gas tank 10/14/2019 Finished install of fuel lines 10/15/2019 Cleaned conv top manual spring tracks 10/16/2019 Installed LH door latch, finished installing brake line, assembled headlight 10/17/2019 Assembled headlight doors, installed end screws on rocker spears 10/19/2019 Sandblasted and painted door glass hardware 10/21/2019 Installed conv top frame 10/22/2019 Cleaned window regulators 10/23/2019 Shipped parts out for rechroming 10/23/2019 Installed RH door regulator and inside latch. Started fixing LH regulator 10/24/2019 Installed RH door regulator and inside latch. 10/26/2019 Sandblasted and painted vent window frames. Installed quarter window regulators. 10/27/2019 Undercoated inside of quarter windows. Paint RH quarter window guide 10/29/2019 install quarter window guides.sandblasted & painted quarter window and RH door glass brackets. 10/30/2019 cleaned glass 10/31/2019 Glued in rear bow tack strip 11/2/2019 Installed rear bow tack strip, stripped down seat frames 11/9/2019 Removed seat upholstery 11/23/2019 Painted steering wheel & B-pillar welting 11/25/2019 Install quarter widow glass moldings 11/26/2019 Installed rear quarter windows and sweeps 11/27/2019 Painted seat frames 11/29/2019 Painted front seat back braces silver 11/30/2019 Installed foam on front seat bottoms 12/2/2019 Installed foam on front seat backs 12/3/2019 Installed cover on RH front seat bottom 12/4/2019 Installed covers on LH front seat bottom and LH front seat back 12/5/2019 Installed cover on RH front seat back 12/7/2019 Installed cover on rear seat back. Installed foam on armrest panels, installed cover on RH rear armrest panel. 12/9/2019 Installed covers on RH upper arm rest and LH lower armrest 12/11/2019 Installed cover on RH upper armrest panel 12/13/2019 Painted LH windshield interior pillar molding 12/14/2019 Installed windowshield frame moldings 12/15/2019 Started to installed Conv well molding 12/17/2019 Finished installing conv well moldings 12/18/2019 Installed door handles, started assembly of vent windows. 12/21/2019 Assembled vent windows 12/22/2019 Installed vent windows, installed RH door glass, Installed wiper transmission 12/27/2019 Sandblasted seat tracks 1/1/2020 Assembled seat tracks, painted seat track springs, Installed RH door weather seals 1/3/2020 Assemble front seats 1/4/2020 Dismantled console. Fixed front seat back panels 1/18/2020 Installed windshield 1/21/2020 Polished and installed windshield moldings. 1/23/2020 Installed lower windshield molding 1/27/2020 Removed bearing from Muncie input shaft 1/28/2020 Masked Muncie case for beadblasting 2/1/2020 Beadblasted trans case, bell housing and distributor body 2/3/2020 Started rebuilding transmission 2/4/2020 Had blue material sewn on top boot, Continued rebuilding transmission 2/8/2020 Started installing well liner and rear window. 2/10/2020 Having trouble with rear window 2/11/2020 Still have trouble with rear window 2/11/2020 Removed rear window 2/15/2020 Installed rear window, started installing conv top 2/17/2020 Continued working on conv top. 2/19/2020 Continued working on conv top. 2/20/2020 Installed conv top front seal. 2/22/2020 Finished convertible top install. 2/24/2020 Installed underlayment. Started to install carpet 2/26/2020 Installed front carpet. Almost finished final install 2/27/2020 Finished installing carpets. Assembled and installed RH rear armrest 2/29/2020 Installed RH door panel. Will need to remove to install correct window regulator 3/2/2020 Rebuilding window crank handles 3/3/2020 Finished rebuilding window crank handles 3/4/2020 Worked on LH door, removed regulator, drilled holes for panel, added weather seal. Added trim and emblem to LH door panel. Installed front outer seatbelts 3/7/2020 Replaced door window regulators, installed LH door glass and weather shield, installed LH rear quarter window side cover. 3/9/2020 Installed front seats 3/10/2020 Installes steering wheel. Finished LH door 3/11/2020 Assembled and Installed LH rear armrest panel asby 3/12/2020 Installed rear seatbelts and upper seat section 3/14/2020 Restored distributor. Sandblasted front seat backs, starter & Z-bar 3/16/2020 Rebuilt starter (ready for paint), removed fabric from lower rear seat 3/21/2020 Installed wheel well moldings (3) 3/23/2020 Installed last wheel well molding 3/25/2020 Assembled shifter to transmission 3/28/2020 painted bellhousing and trans lower cover, fitted small parts to engine 3/31/2020 Repainted B-pillar welting caps 4/2/2020 Installed B-pillar welting caps 4/4/2020 Sandblasted, painted, baked exhaust manifolds, Connected flywheel, clutch, starter, trans to engine 4/6/2020 Prepared engine for install 4/8/2020 Installed Engine 4/9/2020 Finished engine install 4/11/2020 Sandblasted & painte hood hinges. Installed sparkplug wires, coil, etc 4/13/2020 Installed gas pedal, fuel hose nad PCV bracket 4/15/2020 Installed hood hinges and alternator 4/18/2020 Installed hood and Z-bar 4/23/2020 Adjusted clutch, installed long exhaust pipes 4/25/2020 Sandblasted, primed & painted bumper brackets 4/28/2020 Installed rear bumper 5/2/2020 Sandblasted and painted radiator & hood latches. Phosphated hood latches. 5/4/2020 Installed hood latch & radiator 5/16/2020 Removed front filler panel and masked car for nose stripe 5/20/2020 Painted nose stripe 5/21/2020 Drilled nose SS emblem holes, Buffed nose stripe 5/23/2020 Installed front bumper and SS emblems. Repainted upper filler panel stripe 5/24/2020 Masked pinstripe and stencil 5/26/2020 Installed RH headlight asby 5/27/2020 Installed LH headlight asby 5/28/2020 Painted pinstripes 5/30/2020 Unmasked car, installed outside mirror 6/3/2020 Ordered rear end from Camaro Specialties 6/8/2020 Picked up rear end at shop 6/9/2020 Removed brakes from rear end 6/10/2020 Finished dismantling rear end 6/13/2020 Removed springs from old rear end 6/17/2020 Sent rear end parts out to be sandblasted 6/20/2020 Got rear end parts from blaster 6/24/2020 Touchup sandblasting and primed rear end parts 6/25/2020 Painted rear end parts. 6/27/2020 Sandblasted and paint rear brake parts 6/29/2020 Assmebled rear brakes 6/30/2020 Assembled rear end 7/1/2020 Installed rear leaf springs 7/11/2020 Installed seat back panels 7/15/2020 Primed rear brake drums 7/22/2020 Painted rear brake drums and LH shock plate 7/25/2020 Finished install of rear end and exhaust system. E-brake cable too long…… 7/27/2020 Removed radiator to fix pitting 7/28/2020 Painted top of radiator 7/29/2020 Reisntalled radiator 7/30/2020 Finished installing parking brake cables 8/7/2020 Restored driveshaft, less slip yoke 8/10/2020 Installed new slip yoke, U-joints and painted white & orange stripes 8/11/2020 Approved console chroming. Had tires mounted, installed driveshaft, replaced diff plug, bleed rear brakes and installed rear tires. 9/5/2020 Painted console top and gauge housing black 9/16/2020 Painted bottom of console blue 9/17/2020 Flocked inside of console 9/23/2020 Assembled gauges 9/24/2020 Finished assembly console 9/29/2020 Installed console 9/30/2020 Fixed interior lights not coming on - console clock shorted to gnd 10/3/2020 Started car for the first time - had to sand points. 10/6/2020 Installed wipers, Fixed wiper motor not turning off- had to readjust switch on controls |